5V 5.5V 160mA 200mA 250mA 1W 1.25W Solar panel with Solar min battery

Solar Charger

This is a supper mini Solar Lipo charger based on the CN3065 - a single lithium battery charge management chip.

This Solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is easy as well, just plug your solar panel into one side of the Solar charger and your battery into the other and you are good to start charging!

The output of the Solar Charger is intended to charge a single polymer lithium ion cell. The load should be connected in parallel with the battery. By default, the Solar charge comes set to a maximum charge current of 500mA with a maximum recommended input of 6V (minimum 4.4V). It’s recommended that batteries not be charged at greater than their capacity rating.

Features:

Solar panel input: 4.4-6V

Max charge current: 500Ma

Interface: 2-pin JST connectors(or PH2.0)

Short circuit protection

Continuous Charge Current Up to 500mA

Battery status indication ( Red : Charging , Green: Charged )

Micro-USB Connector

Feature:

Input voltage: select the corresponding module according to the nominal voltage of the solar panel (6V/9V/12V)

Output voltage: nominal 3.7V full charge voltage 4.2V lithium battery

Interface: 2-pin JST connectors (or PH2.0)

Solar panel maximum power point tracking

Complete charge management for single-cell lithium batteries

Charging current up to 2A

PWM switching frequency: 300KHz

Charging voltage: 4.2V ± 1%

Trickle charging of deeply discharged batteries

Automatic recharge

Charge status and charge end status indication

Soft start

Battery overvoltage protection

Working environment temperature: -40 ° C to +85 ° C

Size：45X20X9.5mm

5V 160mA 0.8W Solar Panel

Size :70*90MM

Rated Voltage：5V

Rated Current:160mA

Max Power: 0.8W

5V 200mA 1W Solar Panel

Size :70*100MM

Rated Voltage：5V

Rated Current:200mA

Max Power: 1W

5V 250mA 1.25W Solar Panel

Size :69*110MM

Rated Voltage：5V

Rated Current:250mA

Max Power: 1.25W

5.5V 180mA 1W Solar Panel

Size :95*95MM

Rated Voltage：5.5V

Rated Current:180mA

Max Power: 1W

5.5V 291mA 1.6W Solar Panel

Size :150*85MM

Rated Voltage：5.5V

Rated Current:291mA

Max Power: 1.6W

1S Power display

How to use: Connect the positive and negative terminals of the display board to the positive and negative terminals of the battery under test, and the digital tube displays the real-time battery power

Display battery parameters:

 
(Remarks: N is the number of battery cells) (The following data is a reference value, there will be an error range of about 2%, do not shoot if high accuracy is required)

 

The battery voltage is greater than N × 3.3V, with 1 grid lit
The battery voltage is greater than N × 3.5V, with 2 grids on

The battery voltage is greater than N × 3.7V, with 3 grids on

The battery voltage is greater than N × 3.9V, with 4 grids on



The battery voltage is less than N × 3.3V, and the four-segment display is all off, indicating that the battery is below 3.3V, and it is time to charge the battery.

1S 18650 Battery Holder

CH2 Quick Splice Lock Wire Connector

All set Package Include (battery not include )

1* Solar Panel

1*1S display

1* Solar charger

2* 1S battery Holder

1* CH2 Connector

3* Cable